Question 1

Refer to the exhibit R2 can reach Loopback222, but R1 SW1 and PC1 cannot communicate with 172.16.222 254 R1 and R2 configurations are shown here

Which EIGRP configuration command resolves the issue?

Options :

A : R2(config-router) # redistribute static

B : R1(conftg-router)# network 172.16.222.254 0.0.0.0

C : R1 (config-router)# network 172.16.222.264 255.255.255.255

D : R1(config-router)# redistribute static

Answer: A

Question 2

Refer to the exhibit.

An engineer must filter incoming EIGRP updates to allow only a set of specific prefixes. The distribute list is tested, and it filters out all routes except network 10.10.10.0/24. How should the engineer temporarily allow all prefixes to be learned by the routers again without adjusting the existing access list?

Options :

A :

A permit 20 statement should be added before completing the ACL with the required prefixes, and then the permit 20 statement can be removed.

B :

A permit any statement should be added before completing the ACL with the required prefixes and then the permit any statement can be removed.

C :

A continue statement should be added within the permit 10 statement before completing the ACL with the required prefixes, and then the continue statement can be removed.

D : An extended access list must be used instead of a standard access list to accomplish the task

Answer: C

Question 3

What is an advantage of implementing BFD?

Options :

A : BFD provides faster updates for any flapping route.

B : BFD provides millisecond failure detection

C : BFD is deployed without the need to run any routing protocol

D : BFD provides better capabilities to maintain the routing table

Answer: B

Question 4

Refer to the exhibit. An IPv6 ACL is applied to restrict PC1 from communicating with PC2 and allow all other traffic. Which configuration resolves the issue?

Options :

A : R3(config-ipv6-acl)#no sequence 20

R3(config-ipv6-acl)#deny ipv6 host 2001:DB8:0:10::3B host 2001:DB8:A:A::19 sequence 10

B : R3(ccnfig-ipv6-acl)#no sequence 30

R3(config-ipv6-acl)#deny ipv6 host 2001:DB8:0:10::3B host 2001:DB8:A:A::19 sequence 10

C : R3(config-lpv6-acl)#no sequence 20

R3(config-ipv6-acl)#deny ipv6 host 2001:DB8:0:10::3B any sequence 10

D : R3(config-ipv6-acl)#no sequence 30

R3(config-ipv6-acl)#deny ipv6 host 2001:DB8:0:10::3B any sequence 10

Answer: B

Question 5

Refer to Exhibit.

Traffic from the branch network should route through HQ R1 unless the path is unavailable. An engineer tests this functionality by shutting down interface on the BRANCH router toward HQ_R1 router but 192.168.20.0/24 is no longer reachable from the branch router. Which set of configurations resolves the issue?

Options :

A :

HQ_R1(config)# ip sla responder HQ_R1(config)# ip sla responder icmp-echo 172.16.35.2

B :

BRANCH(config)# ip sla 1 BRANCH(config-ip-sla)# icmp-echo 172.16.35.1

C :

HQ_R2(config)# ip sla responder HQ_R2(config)# ip sla responder icmp-echo 172.16.35.5

D :

BRANCH(config)# ip sla 1 BRANCH(config-ip-sla)# icmp-echo 172.16.35.2

Answer: D

Confidently Practice Online with Free 300-410 Exam Cram

Buying Options: