Question 1

What are the main characteristics of the 6 GHz band?

Options :

A : Less RF signal is absorb by objects in a 6 GHz WLAN.

B : In North America, the 6 GHz band offers more 80 MHz channels than there are 40 MHz channels in the 5 GHz band.

C : The 6 GHz band is fully backward compatible with the existing bands.

D : Low Power Devices are allowed for indoor and outdoor usage.

Answer: B

Question 2

You are working with a pair of 6300M switches in a VSF stack. The switch has 48 SmartRate 5G ports, 2 SFP28 ports, and 2 SFP56 ports. Both SFP56 ports are used for stacking. You need to provide an LACP connection to another identical stack with the maximum available bandwidth possible. What should you configure?

Options :

A : a 16-member LAG using 2 SFP28 ports and 6 SR5 ports on each switch

B : an eight-member LAG using 4 SR5 ports on each switch

C : an eight-member LAG using 2 SFP28 ports and 2 SR5 ports on each switch

D : a four-member LAG using 2 SFP28 ports on each switch

Answer: A

Question 3

Describe the purpose of the administrative distance

Options :

A : Routes teamed via external BGP have a higher administrative distance than routes learned via OSPF

B : The administrative distance is used as a trust rating tor route entries

C : The administrative distance for a static route is 10

D : The higher administrative distance is preferred

Answer: B

Question 4

What happens when the signal from an AP weakens by being absorbed as it moves through an object?

Options :

A : APs will use bonded channels to decrease latency to clients

B : Signal to Noise Ratio (SNR) increases

C : Signal to Noise Ratio (SNR) decreases

D : Aruba Central dynamically moves clients to neighboring APs

Answer: C

Question 5

You have been asked to onboard a new Aruba 6300M in a customer deployment You are working remotely rather than on-site You have a colleague installing the switch The colleague has provided you with a remote console session to configure the edge switch You have been asked to configure a link aggregation going back to the cores using interfaces 1/1/51 and 1/1/52 The Senior Engineer of the project has asked you to configure the switch and 1Q uplink with these guidelines 1. Add VLAN 20 to the local VLAN database with name Mgmt 2. Add L3 SVl on VLAN 20 for Management using address 10 in the 10.1.1 0/24 subnet 3. Add LAG 1 using LACP mode active for the uplink 4 use vlan 20 as the native vlan on the LAG 5. Make sure the interfaces are all ON. Which configuration script will achieve the task?

Options :

A : Edge1# conf t vlan 20 name Mgmt interface vlan 20 ip address 10.1.1.10/24 no shut interface lag 1 shut vlan access 20 lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut

B : Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1.1 10/24 no shut interface 1/1/51.1/1/52 shut vlan trunk native 20 vlan trunk allowed all lag 1 lacp mode active interface 1/1/51.1/1/52 no shut

C : Edgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1 1 10/24 no shut interface lag 1 shut vlan trunk native 20 vlan trunk allowed all lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut interface 1/1/51.1/1/52 no shut

D : conf t vlan 20 name Mgmt ip address 10 1 1.10/24 no shut interface lag 1 shut vlan trunk native 1 vlan trunk allowed all lacp mode active int 1/1/51.1/1/52 shut no routing interface lag 1 no shut interface 1/1/51.1/1/52 no shut

Answer: C

Confidently Practice Online with Free HPE6-A85 Exam Cram

Buying Options: